Quick answer: Cat6A cable is rated to 500 MHz and carries 10GBASE-T across the full 100 m channel, which Cat6 manages only to about 55 m. Unshielded Cat6A suits most Australian homes, while shielded F/UTP earns its cost beside mains cabling or in workshops. Budget AU$220 to AU$390 for a 305 m box and buy jacks of the same category. Match the patch panel too, because a mismatched jack loses more margin than the cable costs to buy. Check the box label before paying.
The NBN box sits in the garage, the office is at the back of the house, and the run measures 40 m. Cat6 would carry 1 Gbit/s without complaint, but 10 Gbit/s over that distance needs the extra margin of Cat6A. The cable is the cheap part of the job; the terminations are where the installation fails, and the jacks decide whether the speed holds.
500 MHz and the 100 m Channel
What the frequency rating means
A category rating describes tested performance up to a frequency, not a speed. Cat6A is characterised to 500 MHz with tighter crosstalk limits than Cat6 at 250 MHz. 10GBASE-T uses all four pairs in both directions at once, which is why alien crosstalk between neighbouring cables matters far more than it did at 1 Gbit/s.
The channel includes the patch leads
The 100 m channel covers 90 m of permanent link plus 10 m of patch leads. A 95 m pull with two 3 m leads fails the standard even when the cable itself is perfect. Measure the path with a wheel before ordering a box, and write the length on each outlet.
| Category | Bandwidth | 10G reach | Shielding | AUD per 305 m |
|---|
| Cat5e | 100 MHz | 30 m to 45 m | UTP | AU$90 to AU$140 |
| Cat6 | 250 MHz | 55 m | UTP | AU$140 to AU$220 |
| Cat6A UTP | 500 MHz | 100 m | UTP | AU$220 to AU$330 |
| Cat6A F/UTP | 500 MHz | 100 m | Foil | AU$260 to AU$390 |
| Cat8 | 2000 MHz | 30 m | Foil | AU$450 to AU$700 |
Shielded or Unshielded Cable
When foil earns its price
Unshielded Cat6A handles most homes and offices. Shielded F/UTP is worth the extra where cables share a tray with 240 V mains, near lift motors, or in workshops with welders. The foil blocks interference only when it is bonded to earth at both ends through the jack.
Earthing a shielded run
A shielded cable terminated into unshielded jacks behaves like an antenna and can perform worse than UTP. If you buy foil, buy shielded jacks and a patch panel with a bonded bar, then keep the drain wire short at each end and test for continuity to earth.
Termination Decides the Result
Jacks and pair twist
A certified cable performs only as well as its termination. Cheap jacks with short blades and long untwisted pairs at the punch down add near end crosstalk, and 10GBASE-T has little tolerance for it. Buy jacks rated to the same category and keep the pair twist within 13 mm of the punch.
Testing at the speed you will run
Test every run with a certifier, or at least a qualification tester that reports pair length, wire map and crosstalk margin. A link that passes at 1 Gbit/s can still fail at 10 Gbit/s, so test at the speed the switch will actually negotiate.
NBN, PoE and Real Cable Runs
PoE cameras and access points push 30 W to 90 W down the cable, and a bundle in a hot roof space runs warmer again. Cat6A has thicker conductors than Cat5e, so voltage drop over 60 m is lower, but never bundle more than 24 cables without spacing. A ready made 50 foot ethernet cable in Cat6A covers the last 15 m to a camera without a crimp tool.
Send the run lengths, the outlet count and whether the path shares a tray with mains to zongcarrie@zh-zong.com or call +86 13543026126. We will confirm category, shielding and jack type, then quote in AUD per box and per outlet with freight included.
Ordering Cable and Jacks Together
Buy cable, jacks and patch leads in one order so the categories match. The ethernet plug buying guide is worth reading before choosing field plugs, because most 10G failures at a plug come from the plug rather than from the cable.
Match the RJ45 keystone jack to the cable as well: Cat6A jacks have a wider entry and larger blades than Cat6 parts. Mixing the two is the fastest way to lose margin on a run that tested clean on the drum.
Practical scenarios
- Situation: A double brick home in Sydney needs a 10G link from the garage NBN box to a study 35 m away. What to do: Pull Cat6A UTP in conduit, terminate on Cat6A keystones and test both ends before closing the wall.
- Situation: A warehouse in Western Sydney runs trays beside 240 V mains for 60 m. What to do: Use shielded F/UTP Cat6A with shielded jacks and bond the foil at the patch panel.
- Situation: A Melbourne apartment has strata rules against new penetrations. What to do: Reuse the existing conduit with Cat6A and keep inside the 90 m permanent link limit.
- Situation: A school lab in Perth needs 24 outlets for 10G switches. What to do: Order two 305 m boxes plus Cat6A jacks, then qualify every link before handover.
FAQ
Is Cat6A worth it over Cat6 at home?
Only for runs near or beyond 55 m, or where 10G is planned. On a 20 m run at 1 Gbit/s, Cat6 performs identically and costs less. Buy Cat6A when the cable goes into a wall that will not be opened again.
Can I use Cat6 jacks on Cat6A cable?
Physically sometimes, electrically no. Cat6A has larger conductors and tighter crosstalk limits, and a Cat6 jack will not hold the margin at 500 MHz. Match the jack, the patch panel and the patch leads to the cable category, and the faceplate as well.
Does Cat6A need special tools?
The same punch down tool works, but Cat6A jacks are wider and the pair separation is larger, so trim carefully. A qualification tester that reports margin is far more useful than a basic continuity tester for 10G work. Test one box on arrival before the pull starts.