XLR to TRRS Cable: Balanced Source, Unbalanced Destination
Quick answer / TL;DR: Short answer: use an XLR to TRRS cable where the destination is a camera or phone with a TRRS input, and confirm the wiring matches the device's expected contact order, because CTIA and OMTP differ. The connection is unbalanced, so keep it short. Never connect a cable wired for phantom power to a camera input, and switch phantom off at the mixer unless the microphone requires it. Expect a level mismatch that needs adjustment at the camera.
Four audio lines: balanced XLR, TRS, unbalanced RCA, and speaker cable.This cable connects a microphone or mixer with an XLR output to a camera, phone or recorder with a 3.5 mm TRRS input. It is common in video production, where the camera's audio input is a small jack and the microphone is professional.
The result is unbalanced, because the destination is. The cable's job is to do that conversion without creating a hum loop or feeding phantom power into equipment that cannot tolerate it.
Wiring and Contact Order
The XLR side is unambiguous: pin 1 shield, pin 2 hot, pin 3 cold. The TRRS side is where conventions differ, because the microphone and ground contacts can be in either order.
| Convention | Contact order | Common on |
|---|
| CTIA | tip, ring, ring, sleeve, with mic then ground | most modern phones | OMTP | ground and mic swapped | older devices | Camera input | usually tip and sleeve for mic | device dependent |
A cable built for one convention can produce a weak, noisy or one-sided signal on a device using the other. That is a wiring mismatch rather than a defective cable.
Phantom Power Is the Real Risk
Condenser microphones need phantom power, which is 48 V applied across pins 2 and 3. A camera input is not designed to receive it.
- Switch phantom off at the mixer unless the microphone requires it
- Never connect a phantom-powered line to a camera input
- A blocking capacitor in the cable protects the destination, but few cables include one
- If the microphone needs phantom, power it separately and feed line level to the camera
Real-World Applications
Camera with a 3.5 mm microphone input
A small shotgun or lavalier with an XLR output into a camera. The cable converts connectors, and the camera's own preamp sets the level. Keep the run short and switch phantom off.
Phone or tablet recording
An interviewer's microphone into a phone for a quick recording. Confirm the phone expects a TRRS microphone rather than a headset, and check the contact order.
Field recorder with a small input
Some recorders offer a 3.5 mm input alongside XLRs. Using the small input for a distant microphone is a compromise; the XLR input is preferable where available.
Where this cable is the wrong tool
Any situation where the run must be long, or where a balanced connection is required. A small mixer or a wireless link is the correct solution in both cases.
Related reading: Balanced and unbalanced connections — blogs/news/trs-vs-ts-cable
Related reading: Pole counts on 3.5 mm jacks — blogs/news/3-5mm-aux-cable
Standards and Verification
The XLR connector is standardised in IEC 61076-2-103, with pin 1 as shield, pin 2 as hot and pin 3 as cold. The 3.5 mm jack is dimensioned in IEC 60130-8, but the TRRS contact order is not covered by it, which is why two conventions exist.
Verify wiring with a meter before use: pin 2 to tip, pin 1 and pin 3 to sleeve or ring according to the device's expectation. A cable that works on one camera and not another is usually a contact-order difference.
Check the level by recording a test passage and listening at a realistic gain. A signal that is too hot will clip the camera preamp, and one that is too low will need gain that raises the noise floor.
Label the cable with the convention it uses. In a kit with several similar cables, the one wired for the other convention is a fault that appears only on a specific device.
Frequently Asked Questions
Is an XLR to TRRS cable balanced?
No. The destination is unbalanced, so the whole connection is unbalanced regardless of the XLR connector.
Can phantom power damage my camera?
It can. Switch phantom off at the mixer unless the microphone requires it, and never connect a powered line to a camera input.
Why does my microphone sound weak or noisy?
Often a TRRS contact-order mismatch between the cable and the device. Check whether the device follows CTIA or OMTP.
How long can the cable be?
Keep it short, typically under 3 m. Unbalanced connections pick up interference over distance.
Do I need a preamp?
If the microphone is dynamic and the camera's preamp is weak, yes. A small preamp or a mixer improves the signal-to-noise ratio considerably.
Sourcing cables for a project, a store, or a private-label line? Contact our B2B sales team for specifications, certification evidence, and volume terms – FOB and CIF options available. Request a quote or sample.