Quick Answer: In a ceiling void the cable must satisfy the building before it satisfies the amplifier. Specify a jacket the fire specification accepts, often low smoke zero halogen, keep the run clear of mains cable and support it so its weight does not hang on the terminals. Then size the copper: 2.5 mm squared for an 8 ohm load out to about 28 m, 1.5 mm squared for short runs. Keep total loop resistance under roughly 5 per cent of the speaker impedance, a rule of thumb that preserves damping.
Ceiling speakers are installed once and then forgotten, which is why the cable is usually chosen on price and regretted later. The amplifier sees only loop resistance, but the building sees the jacket, the containment and the route. Two separate approvals are involved, and the fire performance one is the harder to change after the ceiling is closed.
The void decides before the amplifier does
A ceiling void is often a fire compartment, a return air path, or both. Cable lying in it becomes part of that compartment, so the jacket has to be acceptable to whoever signs the building off. That requirement is decided early and is expensive to reverse once the boards are fixed.
Fire performance and jacket choice
Low smoke zero halogen compounds are the usual answer where a specification calls for limited smoke and no halogen acid gas. PVC is cheaper and common in domestic voids. Ask what the specification names rather than assuming it, because in-wall speaker wire with the wrong jacket can fail an inspection after the plaster is up.
Separation and support
Keep loudspeaker cable clear of mains cable in the same void; the wiring regulations treat them as different bands and require separation. Support the run so its weight does not hang on a terminal, and avoid tight cable ties, which deform the insulation and press the conductors together.
Gauge against an 8 ohm load
The amplifier drives a low impedance, so every ohm of cable resistance is a fraction of the load it cannot control. A long thin run raises loop resistance, wastes output and tilts the response as the speaker impedance varies with frequency. Copper cross-section is the only useful lever.
Why 2.5 mm squared for long runs
At 8 ohm, 2.5 mm squared speaker cable adds about 1.4 ohm per 100 m of loop, so a 25 m run stays near 0.35 ohm, comfortably under 5 per cent of the load. A 1.5 mm squared cable reaches the same fraction at about 17 m. That 5 per cent figure is a rule of thumb, not a standard.
Matching copper to run length
Measure the real route, including vertical drops and the service loop left at each speaker, then read the cross-section from the loop resistance. Standard 16 gauge speaker wire is about 1.3 mm squared, which sits awkwardly between the two sizes people actually stock.
| Cross-section | Loop resistance | Run at 8 ohm | Use |
|---|
| 0.75 mm squared | About 4.6 ohm per 100 m | Up to 8 m | Short domestic drops |
| 1.5 mm squared | About 2.3 ohm per 100 m | Up to 17 m | Short runs at 8 ohm |
| 2.5 mm squared | About 1.4 ohm per 100 m | Up to 28 m | Long runs at 8 ohm |
| 4 mm squared | About 0.9 ohm per 100 m | Up to 45 m | 4 ohm loads or very long runs |
Practical scenarios
- Situation: Eight 8 ohm ceiling speakers on one channel wired in parallel. The load falls to 1 ohm, so use a transformer tap or a distribution amplifier rather than thicker cable.
- Situation: A 30 m run to a single 8 ohm ceiling speaker. Move up to 4 mm squared; 1.5 mm squared adds about 0.7 ohm of loop and audibly softens the low end.
- Situation: The void is a fire compartment and the specification names low smoke zero halogen. Buy that jacket, keep the certificate with the job file and do not substitute PVC to save a margin.
- Situation: The route must cross a mains lighting circuit. Maintain separation along the run and cross at right angles where the two have to meet.
FAQ
Can I use twin and earth for ceiling speakers?
It works electrically but it is the wrong product. Twin and earth is solid-core mains cable with a bare circuit protective conductor, which is stiff, awkward at a speaker terminal and not made for the purpose. Stranded cable of the right cross-section installs faster and handles better.
Does thicker copper improve the sound?
Only where loop resistance is already significant. Below about 5 per cent of the speaker impedance the audible difference is small; above it, thicker copper restores output and low-frequency control. A 4 mm squared cable on a 5 m run at 8 ohm buys very little.
Is 1.5 mm squared enough?
For short runs at 8 ohm, yes: it holds the 5 per cent rule to roughly 17 m. Longer routes, 4 ohm loads and parallel pairs need more copper. Where the ceiling will be closed for years, specify 2.5 mm squared now rather than reworking later.