HDMI 1.4 vs 2.0: Bandwidth, 4K60 and HDR
Quick answer / TL;DR: Short answer: HDMI 1.4 provides up to 10.2 Gbps, enough for 4K at 30 Hz, and introduced the Ethernet channel and ARC. HDMI 2.0 raises the link to 18 Gbps, which is what allows 4K at 60 Hz with 8-bit 4:4:4 or 10-bit at reduced chroma, plus HDR metadata. Cables are not versioned: a High Speed cable is rated around 10.2 Gbps and a Premium High Speed cable at 18 Gbps, so the cable class is what you buy, and the port version is what the device supports.
Three lanes in one cable: video, audio, and the HEC that rarely gets used.The step from HDMI 1.4 to 2.0 was mostly a bandwidth increase, and that increase is what made 4K practical. At 1.4 rates, 4K is limited to 30 Hz; at 2.0 rates, 4K60 with HDR fits.
The practical confusion is that version numbers belong to ports and chips, not to cables. A cable is characterised by the bandwidth class it passes, which is why a cable labelled 1.4 may be perfectly adequate for a 2.0 link.
What Changed at 2.0
Three things changed that matter to a user: the link rate, the maximum 4K frame rate, and the metadata path for high dynamic range. Everything else was refinement.
| Feature | HDMI 1.4 | HDMI 2.0 |
|---|
| Max link rate | 10.2 Gbps | 18 Gbps |
| 4K maximum refresh | 30 Hz | 60 Hz |
| HDR metadata | not supported | static metadata, CTA-861.3 |
| Colour at 4K60 | not achievable | 8-bit 4:4:4 or 10-bit 4:2:0 |
| ARC | yes | yes, with more channel capacity |
| Ethernet channel (HEC) | introduced | retained |
| 3D | supported | retained but rarely used |
The 4K60 row is the one that decides purchases. A 1.4 link physically cannot carry 4K60 at 8-bit 4:4:4, because the payload exceeds 10.2 Gbps. Devices that advertise 4K60 over a 1.4 port are using chroma subsampling or a reduced colour depth.
Cables Are Classed, Not Versioned
This is the point that saves money. The HDMI specification version describes what a port or chip can do. A cable is described by the bandwidth class it has been tested to, and the classes map onto versions only loosely.
| Cable class | Tested bandwidth | Suitable for |
|---|
| Standard (Category 1) | about 2.25 Gbps per channel group | 1080i and below |
| High Speed (Category 2) | about 10.2 Gbps total | 1080p, 4K30 |
| Premium High Speed | 18 Gbps | 4K60, HDR |
| Ultra High Speed | 48 Gbps | 4K120, 8K |
A High Speed cable will not carry a 4K60 signal regardless of what the port supports, and a Premium High Speed cable will carry 4K60 even though it may be sold without a 2.0 label. The class is the buying decision.
Where the Differences Show Up in Practice
HDR collapses to SDR
Enabling HDR raises the payload, which pushes a marginal link over its budget. A 4K60 SDR signal fits 10.2 Gbps; the same content in HDR does not. The symptom is a picture that works until HDR content starts playing, then falls back or drops out.
4K60 is offered as 4K30
A source connected through a 1.4-class cable or a 1.4 port will cap at 30 Hz. The television reports 4K, so the resolution looks correct, but motion reveals the frame rate. Check the reported refresh, not the reported resolution.
Audio return does not work
ARC needs both ends to support it and the correct input selected. It was introduced at 1.4 and carried forward, so a failure is usually a settings or port-labelling issue rather than a version mismatch.
Real-World Applications
4K television with an older AV receiver
The receiver's HDMI ports are often 1.4 even when the television is 2.0. Routing the source through the receiver caps the whole chain at 1.4, so 4K60 and HDR are unavailable. Connect the source directly to the television and send audio back over ARC or eARC instead.
Upgrading a 1080p installation to 4K60
The cable in the wall may be a High Speed 1.4-era cable, which will not carry 4K60. Verify the class before assuming the display is at fault; a 5 metre in-wall cable of unknown class is the usual culprit.
Desktop 4K60 monitor over HDMI
A Premium High Speed cable at 2 metres is sufficient for 4K60 at 8-bit. At 10-bit, the payload rises and the cable margin shrinks, so buy certified rather than generic at the same class.
Standards and Verification
The versions, rates and metadata are all published, which makes a compatibility question answerable on paper.
- HDMI Licensing Administrator, HDMI 1.4, 2.0 and 2.1 specifications: link rates and the feature sets introduced at each version
- Premium High Speed and Ultra High Speed Cable Certification Programmes: the cable classes and their tested bandwidths
- CTA-861.3: static HDR metadata, the mechanism HDMI 2.0 uses
- CTA-861 series generally: the video formats and timing definitions used by the link
- IEC 62368-1: safety requirements applying to the connected equipment
Verification is a read of two screens. Check the source's output information and the display's input information: both should report the same resolution, refresh, colour depth and HDR state. If the display reports 4K30 while the source is set to 4K60, the chain is capped, and the port version or the cable class is the reason.
Related reading: HDMI cable guide: versions, bandwidth and limits — blogs/news/hdmi-cable
Related reading: HDMI 2.1 cable: what 48 Gbps actually buys — blogs/news/hdmi-2-1-cable
Related reading: HDMI ARC cable: the return channel explained — blogs/news/hdmi-arc-cable
Frequently Asked Questions
Can an HDMI 1.4 cable carry 4K60?
No. HDMI 1.4 rates cap at 10.2 Gbps, and 4K60 at 8-bit 4:4:4 needs about 12.5 Gbps. A Premium High Speed 18 Gbps cable is required for 4K60.
Is HDMI 2.0 backwards compatible with 1.4?
Yes. A 2.0 port works with a 1.4 device at 1.4 capabilities, and a 1.4 cable on a 2.0 port works at 1.4 bandwidth. The link always runs at the lowest common capability.
Does HDMI 2.0 support HDR?
Yes. HDMI 2.0 carries static HDR metadata under CTA-861.3, which covers HDR10 and similar formats. Dynamic metadata formats need later capabilities.
Why does my 4K television show 30 Hz?
The chain is capped at 1.4, either by the cable class, the receiver, or the port. Check the reported refresh at both ends and test with a certified Premium High Speed cable directly into the television.
Do I need an HDMI 2.0 cable?
You need a cable class, not a version. Buy Premium High Speed for 4K60 and Ultra High Speed for 4K120 or 8K. A cable sold as 2.0 without stating the class tells you very little.
Sourcing cables for a project, a store, or a private-label line? Contact our B2B sales team for specifications, certification evidence, and volume terms – FOB and CIF options available. Request a quote or sample.