Cat7 Speed: 600 MHz, Same Ethernet Speeds
Quick answer / TL;DR: Short answer: Cat7 speed is 10 Gb/s over 100 m, identical to Cat6a. It is rated to 600 MHz rather than 500 MHz, which provides margin during testing rather than additional throughput. It does not support 25GBASE-T or 40GBASE-T; those require Cat8 and are limited to 30 m. Any speed gain you see from Cat7 comes from eliminating a faulty cable or connector, not from the category.
The Cat7 connector problem: the cable is rated, the familiar plug is not.The honest answer to how fast Cat7 is: the same as Cat6a for every Ethernet standard in use. Cat7 is rated to 600 MHz, carries 10GBASE-T to 100 m, and does not support 25G or 40GBASE-T at all.
That is not a defect. It is what the category was designed to do. The extra bandwidth over Cat6a exists for margin and for non-Ethernet applications, and buyers who expect a faster network from the higher number end up disappointed for reasons that have nothing to do with the cable.
Speed Is Set by the Standard, Not the Cable
Ethernet speed is negotiated by the network interfaces according to IEEE standards. The cable either supports the required bandwidth or it does not. Once it does, a higher-rated cable cannot make the link faster, in the same way a wider road does not raise the speed limit.
| Standard | Bandwidth needed | Cat6a | Cat7 | Cat8 |
|---|
| 1000BASE-T | 100 MHz | 100 m | 100 m | 100 m | 2.5GBASE-T | 100 MHz | 100 m | 100 m | 100 m | 5GBASE-T | 200 MHz | 100 m | 100 m | 100 m | 10GBASE-T | 500 MHz | 100 m | 100 m | 100 m | 25GBASE-T | 2000 MHz | not supported | not supported | 30 m | 40GBASE-T | 2000 MHz | not supported | not supported | 30 m |
The table is the whole story for speed. Cat7 and Cat6a are identical in every row that matters, and both are excluded from the two rows where Cat8 appears. Cat7's 600 MHz never becomes throughput.
What the Extra 100 MHz Buys
The benefit of 600 MHz is margin. When a channel is tested at 500 MHz, a cable rated to 600 MHz has headroom in every parameter: insertion loss, crosstalk and return loss. That margin is what carries a link through six connectors, a tight bend and a warm ceiling void.
In practice this reduces the number of links that fail acceptance testing by a small amount, and it gives a longer service life before the installation drifts out of specification as connectors age. Neither of those shows up as a speed increase.
- Acceptance testing: fewer marginal failures on long or complex channels
- Ageing: more headroom as connectors oxidise and contacts loosen
- EMC: extra shielding depth for emissions-sensitive rooms
- Non-Ethernet uses: headroom for HDBaseT and some AV-over-IP systems
- Nothing: no additional Ethernet speed, no 25G, no 40G
The Connector Decides Whether You Get 600 MHz
This is the practical issue with Cat7 and the reason its reputation is mixed. Standard RJ45 is not specified above Cat6a. A Cat7 channel requires GG45 or TERA connectors. Cat7 cable terminated with RJ45 jacks is a Cat6a channel built on Cat7 cable, and that is what most Cat7 patch cords in circulation actually are.
If the requirement is genuinely 600 MHz, the outlets, panels and patch cords all have to be Cat7 interfaces. If they are RJ45, the money spent on Cat7 cable is buying margin at Cat6a frequencies rather than Cat7 performance.
Real-World Applications
Specifications that name Cat7
Where a tender names Cat7, the category is a compliance question rather than a speed question. Install it with GG45 outlets, document the ISO channel test, and do not promise the client faster networking than Cat6a would have delivered.
AV over IP distribution
Some AV-over-IP systems use bandwidth beyond what 10GBASE-T needs and benefit from Cat7 headroom, particularly where several streams share one link. This is one of the few places where 600 MHz has a real, measurable use.
EMC-sensitive rooms
Cat7 is always shielded, usually S/FTP or F/FTP. In a room that has to pass an emissions test, the shielding and the bandwidth margin both help, and the category is chosen for compliance rather than throughput.
Where Cat7 is simply the wrong answer
Any project whose actual requirement is 10GBASE-T at 100 m. Cat6a does exactly the same job for less money and with far wider availability of connectors. Choosing Cat7 there is paying for a number rather than a capability.
Related reading: Cat7 cable and its 600 MHz rating — blogs/news/cat7-cable
Related reading: Which connector a Cat7 channel needs — blogs/news/cat7-connector-problem
Standards and Verification
Cat7 is defined in ISO/IEC 11801-1 at 600 MHz. It is not a TIA category, so a North American project using it is working to ISO and the acceptance documentation should state that. Component requirements are in IEC 61156-5.
Ethernet speeds are defined separately by IEEE 802.3: 1000BASE-T in 802.3ab, 10GBASE-T in 802.3an, 25GBASE-T in 802.3bp and 40GBASE-T in 802.3bq. Those standards set the bandwidth requirement the cable has to meet, which is why a higher category cannot exceed them.
Ask for a 600 MHz channel test report naming the connectors used. If the report was produced with RJ45 jacks, the result describes a Cat6a channel and should not be presented as Cat7 evidence.
Beware listings that describe Cat7 as supporting 40G or 100G. Neither is achievable over Cat7. 40GBASE-T requires Cat8 within 30 m, and 100G over copper is not a defined standard for twisted pair in commercial use.
Frequently Asked Questions
How fast is Cat7?
10 Gb/s over 100 m, the same as Cat6a. It is rated to 600 MHz but no Ethernet standard uses the range between 500 and 600 MHz, so the extra bandwidth does not produce more speed.
Is Cat7 faster than Cat6a?
No. Both support 10GBASE-T to 100 m and neither supports 25GBASE-T or 40GBASE-T. Cat7 offers more test margin, not more throughput.
Does Cat7 support 40 Gigabit?
No. 40GBASE-T requires Cat8 and is limited to a 30 m channel. Cat7 is rated to 600 MHz, while 40GBASE-T needs 2000 MHz.
Why do some Cat7 cables seem faster?
Usually because the previous cable was faulty, marginal or only two-pair, which capped the link at 100 Mb/s. Replacing a bad cable with any compliant cable restores full speed, and the improvement is credited to the category by mistake.
Do I need special connectors for Cat7 speed?
To claim a Cat7 channel you need GG45 or TERA connectors, because RJ45 is not specified above Cat6a. With RJ45 jacks the installation is a Cat6a channel regardless of the cable's rating.
Sourcing cables for a project, a store, or a private-label line? Contact our B2B sales team for specifications, certification evidence, and volume terms – FOB and CIF options available. Request a quote or sample.