Extending HDMI Past 15 Metres With Cat6 Cable
A standard HDMI cable is dependable for about five metres, and even active copper versions rarely pass twenty. When a display sits across a warehouse floor, up in a ceiling mount or inside a lectern, the practical answer is an HDMI over Ethernet extender: a transmitter at the source converts the HDMI signal into a form that travels on Cat6, and a receiver at the far end converts it back. A matched pair usually costs less than fibre HDMI at the same distance, and the cable is cheap to replace.
Quick Answer
An HDMI over Ethernet extender carries HDMI video over one Cat5e or Cat6 cable and reaches 100 metres on solid Cat6. It is a point to point link, not a network device: the transmitter and receiver must be a matched pair and cannot share an Ethernet switch.
| Run length | Plain HDMI | Extender over Cat6 | Notes |
|---|
| Up to 15m | Reliable passive | Not needed | Use a plain cable |
| 30m to 50m | Active HDMI only | Works at 4K 60Hz | Best value option |
| 50m to 100m | Not reliable | Works on solid Cat6 | Longest copper run |
| Over 100m | Not possible | Fibre HDMI needed | Specialised install |
How the Transmitter and Receiver Pair Works
The transmitter takes the HDMI data stream and drives it as a balanced signal over twisted pairs. Most units send video on three pairs and use the fourth for power, display data and infrared return. Because the signal is point to point, the cable must run directly from one box to the other with no switch, router or patch panel in between.
Power normally comes from a small adapter at one end, and many receivers can be fed over the same Cat6 run. Infrared return is common, so a remote control at the display can operate the source device in another room.
EDID and HDCP Handling
EDID is the data that tells the source which resolutions the display supports. A good extender stores and forwards it, so the source keeps the correct mode when the link reconnects. HDCP 2.2 support is required for protected 4K content, and a unit that only handles HDCP 1.4 will show a black screen on streaming services.
Real Distance and Resolution Limits
Distance and resolution compete for the same bandwidth. At 1080p a quality extender pair will run the full 100 metres on Cat6. At 4K 60Hz the signal needs far more throughput, and many units are specified for 40 to 70 metres at that resolution, or the full 100 metres only at 4K 30Hz.
Cable quality matters more than the marketing sheet. Solid copper Cat6 with 23 AWG conductors holds the signal better than stranded patch cable, and shielded Cat6 helps in rooms with heavy electrical noise.
When Fibre HDMI Is the Better Buy
Beyond 100 metres, or where the cable must pass near motors and dimmers, fibre HDMI or a fibre based extender removes the distance problem entirely. The cost is higher, but the installation becomes immune to electrical interference and to ground loops between buildings.
What to Check Before Installing
Confirm the display native resolution and refresh rate, then read the extender specification at that exact mode rather than at 1080p. Check whether the pair passes HDR, since HDR adds bandwidth and is often dropped on cheaper units even when 4K 60Hz is claimed.
Cable and Connector Discipline
Use Cat6 with solid conductors, terminate both ends to the same wiring standard, and keep the run inside the stated limit. Avoid running the cable parallel to mains wiring for long distances, and label both ends so a future technician knows the link is a video extension rather than a network drop.
Real-World Applications
- A retail store mounts a menu screen eight metres up and thirty metres from the stockroom player. An extender pair over one Cat6 run replaces a long HDMI cable that kept losing signal.
- A church installs a projector at the back of the hall, sixty metres from the media desk. A 4K 30Hz extender pair covers the graphics without the cost of fibre.
- A factory floor monitors a production line from a control room. Shielded Cat6 and an extender immune to motor noise solve interference a passive cable could not handle.
- A conference room uses the ceiling projector as a second display. The extender infrared return lets the presenter change slides with the remote from the table.
Related Guides
For the full product range, browse our productlist. For a deeper dive, read ethernet cable distance limit guide, and for the next step, see hdmi cable 4k.
FAQ
Is HDMI over Ethernet the same as HDMI over IP?
No. An extender is a direct point to point link that behaves like a long cable. HDMI over IP encodes video onto a network, works through switches, but adds latency and often caps at 1080p on affordable units.
Can I connect an HDMI extender through a network switch?
Not with a standard extender pair. The transmitter expects a dedicated cable to its own receiver. Only IP based encoders and decoders are designed to work through a switch.
Does HDMI over Cat6 carry audio?
Yes. Audio travels inside the HDMI stream, so the receiver outputs video and audio together at the display. No separate audio cable is needed at either end.
How much delay does an extender add?
A non compressing extender adds almost none, because it does not decode the video. Units that compress the signal add a few milliseconds, which matters for gaming but not for signage.
Need a custom length, gauge or connector build? Contact our cable team with your spec and quantity.
