Cat7 vs Cat8: Bandwidth Is Not the Deciding Difference
Quick answer / TL;DR: Short answer: choose Cat8 only for 25GBASE-T or 40GBASE-T links under 30 m, typically within a rack or between adjacent racks. Choose Cat7 when the requirement is 10GBASE-T to 100 m with more bandwidth margin than Cat6a, in an ISO-specified building. Cat7 cannot run 25G or 40G at all, and Cat8 cannot run anything beyond 30 m at those speeds. Both are shielded, and both need connector discipline, but Cat8 costs substantially more and is far less available.
Cat8's rating ends at 30 metres: beyond that the standard does not apply.Cat7 and Cat8 are often presented as consecutive steps on a ladder, and that framing produces bad decisions. They are two different ceilings: Cat7 gives 600 MHz with no defined faster-than-10G Ethernet above it, while Cat8 gives 2000 MHz but only across a 30 m channel.
The choice between them is therefore made by distance and link speed, not by which number is larger. A building wired in Cat8 for horizontal runs is not an upgrade over Cat7; it is a specification error.
The Two Numbers That Matter
Bandwidth is the headline and distance is the constraint. Comparing only the bandwidth column makes Cat8 look like a straightforward improvement, which is why the comparison needs both columns together.
| Property | Cat7 | Cat8 |
|---|
| Bandwidth | 600 MHz | 2000 MHz | Standard bodies | ISO only | ISO and TIA | Channel length | 100 m | 30 m at 25G and 40G, 100 m at 10G | 10GBASE-T | 100 m | 100 m | 25GBASE-T | not supported | 30 m | 40GBASE-T | not supported | 30 m | Connector | GG45 or TERA | Cat8.1 RJ45, Cat8.2 GG45 or TERA | Shielding | always shielded | always shielded | Relative price | high | highest |
Read the 25G and 40G rows together with the channel length row, because they only make sense as a pair. Cat8 supports those speeds and only within 30 m. Cat7 does not support them at any distance.
Where Each One Actually Belongs
The application, not the category, should drive the specification. Working from the physical layout backwards is the reliable method.
| Layout | Best category | Reason |
|---|
| Desk to telecom room, 90 m | Cat6a or Cat7 | Cat8 cannot reach at any speed above 10G |
| Cabinet to cabinet, same row, 20 m | Cat8 | short enough for 25G or 40G copper | Top of rack to server, 3 to 10 m | Cat8 | the canonical Cat8 use | Building backbone between floors | fibre | copper category is irrelevant at that distance | Building with an ISO Cat7 mandate | Cat7 | compliance requirement, not a speed one |
The Connector Question Applies to Both
Neither category works properly with ordinary RJ45 jacks at its full rating. Cat7 requires GG45 or TERA. Cat8 splits into Cat8.1, which uses RJ45, and Cat8.2, which uses GG45 or TERA. That means a Cat8.1 installation can keep RJ45 patch cords, while a Cat7 installation generally cannot.
This is the counter-intuitive part of the comparison: Cat8.1 is easier to integrate into an existing RJ45 estate than Cat7 is, because Cat8.1 was defined with RJ45 from the start. A project that chose Cat7 for compatibility reasons may find Cat8.1 more compatible in practice.
- Cat7 with RJ45 jacks: a Cat6a channel on Cat7 cable, not a Cat7 channel
- Cat8.1 with RJ45: a compliant Cat8 channel at 30 m
- Cat8.2 with TERA or GG45: a compliant Cat8 channel, no RJ45 compatibility
- Mixing any of these in one link caps it at the weakest component
Real-World Applications
Data hall server refresh
Servers and switches in one cabinet row, 25G or 40G copper links, runs of 3 to 10 m. Cat8 delivers it passively, and the 30 m limit is irrelevant because the run is a fraction of that. Cat7 here would cap the link at 10G.
Office building with an ISO Cat7 specification
The specification names Cat7, the runs are 60 to 90 m, and the requirement is 10GBASE-T. Cat7 satisfies it with margin. Cat8 in the same building would exceed the 30 m limit at any speed above 10G, so the extra bandwidth would be unusable.
Migration from an existing Cat6a estate
Where the installed base is Cat6a with RJ45, moving to Cat8.1 preserves connector compatibility and adds headroom for short high-speed links. Moving to Cat7 would force a connector change across the estate for no additional Ethernet speed.
Where neither is justified
A 1G network with no 10G plan. Cat6 satisfies it at a fraction of the cost, and neither Cat7 nor Cat8 changes anything measurable. Paying for bandwidth that no planned standard will use is the most common waste in cabling specifications.
Related reading: The Cat7 cable and its 600 MHz rating — blogs/news/cat7-f-ftp-cable
Related reading: Cat8 construction and the 30 metre limit — blogs/news/cat8-cable
Standards and Verification
Cat7 is defined in ISO/IEC 11801-1 at 600 MHz with GG45 or TERA connectors, and has no TIA equivalent. Cat8 is defined in both ISO/IEC 11801-1 and ANSI/TIA-568.2-D at 2000 MHz with a 30 m channel, split into Cat8.1 for RJ45 and Cat8.2 for GG45 or TERA.
The Ethernet speeds themselves come from IEEE 802.3: 10GBASE-T in 802.3an, 25GBASE-T in 802.3bp and 40GBASE-T in 802.3bq. Those standards set the bandwidth requirement, which is why a cable cannot exceed them regardless of its rating.
For Cat8, ask for a 30 m channel test report at 2000 MHz naming the connector and cord models, plus PSANEXT and PSAACRF from a bundle test. For Cat7, ask for a 600 MHz channel report naming GG45 or TERA connectors; a report produced with RJ45 jacks describes a Cat6a channel.
Neither category tolerates careless termination. Both are shielded, so both require a bonded connector and a shield continuity check at commissioning. An unbonded shield turns the cable into an antenna, and the resulting faults look like intermittent negotiation failures rather than cable faults.
Frequently Asked Questions
Is Cat8 better than Cat7?
It has higher bandwidth and supports 25G and 40G, but only within 30 m. For 10GBASE-T at 100 m they are equivalent in capability, and Cat7 is cheaper. Judge by link speed and distance rather than by the category number.
Can Cat7 run 40 Gigabit?
No. Cat7 is rated to 600 MHz and 40GBASE-T requires 2000 MHz. Only Cat8 supports 40GBASE-T, and only to 30 m.
Why is Cat8 limited to 30 metres?
Because 40GBASE-T was specified for data hall distances, and alien crosstalk between parallel cables beyond 30 m cannot be controlled within practical cable designs. The limit belongs to the standard, not to any particular product.
Do both need special connectors?
Cat7 does: GG45 or TERA, because RJ45 is not specified above Cat6a. Cat8 depends on the version: Cat8.1 uses RJ45 and Cat8.2 uses GG45 or TERA. That makes Cat8.1 easier to integrate into an RJ45 estate.
Which should I install in a new office building?
Usually Cat6a, or Cat7 if the specification demands it. Cat8 is a rack-level product and cannot serve horizontal runs at speeds above 10G, so installing it to the desk pays a large premium for capability the distance limit removes.
Sourcing cables for a project, a store, or a private-label line? Contact our B2B sales team for specifications, certification evidence, and volume terms – FOB and CIF options available. Request a quote or sample.